DTC | Description | Action |
|---|---|---|
U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PERFORM the PMI using as-built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC returns, INSTALL a new RTM. REFER to: Radio Transceiver Module (RTM) (419-10 Multifunction Electronic Modules, Removal and Installation). |
U3000:04 | Control Module: System Internal Failure | INSTALL a new RTM. REFER to: Radio Transceiver Module (RTM) (419-10 Multifunction Electronic Modules, Removal and Installation). |
DTC Chart: DDM
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
DDM DTC Chart
DTC | Description | Action |
|---|---|---|
B1088:83 | LIN Bus "B": Value of Signal Protection Calculation Incorrect | REFER to: Glass, Frames and Mechanisms (501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
B1088:87 | LIN Bus "B": Missing Message | REFER to: Glass, Frames and Mechanisms (501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
B108F:23 | Cabin Lock/Unlock Switch: Signal Stuck Low | GO to Pinpoint Test J |
B1163:11 | Left Mirror Heater Output: Circuit Short To Ground | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
B1163:15 | Left Mirror Heater Output: Circuit Short To Battery or Open | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
B1C03:23 Memory #1 Switch: Signal Stuck Low | REFER to: Front Seats (501-10A Front Seats, Diagnosis and Testing). | |
B1C04:23 Memory #2 Switch: Signal Stuck Low | REFER to: Front Seats (501-10A Front Seats, Diagnosis and Testing). | |
B1C05:23 Memory #3 Switch: Signal Stuck Low | REFER to: Front Seats (501-10A Front Seats, Diagnosis and Testing). | |
B1C09:11 | Driver Left/Right Mirror Motor: Circuit Short To Ground | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
B1C09:15 Driver Left/Right Mirror Motor: Circuit Short To Battery or Open | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). | |
B1C10:11 | Driver Up/Down Mirror Motor: Circuit Short To Ground | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
B1C10:15 Driver Up/Down Mirror Motor: Circuit Short To Battery or Open | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). | |
B1C13:11 | Driver Up/Down Mirror Motor Feedback: Circuit Short To Ground | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
B1C13:15 Driver Up/Down Mirror Motor Feedback: Circuit Short To Battery or Open | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). | |
B1C14:11 | Driver Left/Right Mirror Motor Feedback: Circuit Short To Ground | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
B1C14:15 Driver Left/Right Mirror Motor Feedback: Circuit Short To Battery or Open | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). | |
B1D06:11 | Left Turn Indicator: Circuit Short To Ground | REFER to: Turn Signal and Hazard Lamps (417-01 Exterior Lighting, Diagnosis and Testing). |
C1B15:11 | Sensor Supply Voltage B: Circuit Short To Ground | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). |
C1B15:15 Sensor Supply Voltage B: Circuit Short To Battery or Open | REFER to: Rear View Mirrors (501-09 Rear View Mirrors, Diagnosis and Testing). | |
U0010:00 | Medium Speed CAN Communication Bus: No Sub Type Information | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). VERIFY the continuity of the connectors and wiring. Refer to Wiring Diagrams Cell 14 Module Communications Network for schematic and connector information. |
U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test W |
U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test X |
U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new DDM. REFER to: Driver Door Module (DDM) (419-10 Multifunction Electronic Modules, Removal and Installation). |
2016 Mustang workshop publication supplied to Mustang Atlas. Original technical text and illustrations; HTML formatting by Mustang Atlas. Source page numbering is retained for traceability. Follow the configuration, revision, warnings, and cross-references in the material. About this edition.