DTC Description Action retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to the RCM DTC Chart. For BCM Diagnostic Trouble Codes (DTCs), REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Diagnosis and Testing). U0422:81 Invalid Data Received NOTE: This DTC sets in a module that is reporting a missing or invalid From Body Control message from another module on the data bus. The module that reports Module: Invalid Serial the fault is not the problem module. Do not install a new RCM as part of Data Received the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and BCM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to the RCM DTC Chart. For BCM Diagnostic Trouble Codes (DTCs), REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Diagnosis and Testing). U0554:00 Invalid Data Received CHECK for additional RCM and APIM Diagnostic Trouble Codes (DTCs). From Accessory For RCM Diagnostic Trouble Codes (DTCs), REFER to the RCM DTC Protocol Interface Chart. For APIM Diagnostic Trouble Codes (DTCs), Refer to the Module: No Sub Type appropriate section in Group 415 for the procedure. Information U0557:82 Invalid Data Received CHECK for additional RCM and FCIM Diagnostic Trouble Codes (DTCs). From Front Controls For RCM Diagnostic Trouble Codes (DTCs), RETURN to the beginning of Interface Module "A": No this chart. For FCIM Diagnostic Trouble Codes (DTCs), Refer to the Sub Type Information appropriate section in Group 415 for the procedure. U2100:00 Initial Configuration Not CHECK vehicle history for recent service actions related to this module. Complete: No Sub Type This DTC sets due to incomplete or improper PMI procedures. If there Information have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool using As-Built data. U2101:00 Control Module CARRY OUT PMI using As-Built data. RETRIEVE RCM Diagnostic Configuration Trouble Codes (DTCs). If RCM DTC U2101:00 is retrieved on-demand, Incompatible: No Sub INSTALL a new RCM. Use As-Built data when carrying out PMI for this Type Information DTC. REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation). U2200:00 Control Module INSTALL a new RCM. Use As-Built data when CARRYING OUT PMI Configuration Memory during the RCM installation. Corrupt: No Sub Type REFER to: Restraints Control Module (RCM) (501-20B Supplemental Information Restraint System, Removal and Installation). U2300:55 Central Configuration: Not Configured REFER to: Pinpoint Test - DTC: AI (501-20B Supplemental Restraint System, Diagnosis and Testing). U2300:64 Central Configuration: Signal Plausibility Failure REFER to: Pinpoint Test - DTC: AI (501-20B Supplemental Restraint System, Diagnosis and Testing). U3000:46 Control Module: INSTALL a new RCM. Use As-Built data when CARRYING OUT PMI Calibration / Parameter during the RCM installation. Memory Failure REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation). U3000:49 Control Module: Internal INSTALL a new RCM. Using a diagnostic scan tool, CARRY OUT RCM Electronic Failure PMI. If DTC U2200:00 is also present, USE As-Built data when CARRYING OUT PMI during the RCM installation. REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation). U3003:16 Battery Voltage: Circuit Voltage Below Threshold REFER to: Pinpoint Test - DTC: AJ (501-20B Supplemental Restraint System, Diagnosis and Testing).
Original table alignment retained · Scroll horizontally if needed
Source reference 1767
2016 Mustang workshop publication supplied to Mustang Atlas. Original technical text and illustrations; HTML formatting by Mustang Atlas. Source page numbering is retained for traceability. Follow the configuration, revision, warnings, and cross-references in the material. About this edition.